How To Remove a Drop Ceiling

I am not sure what it was about the 80s, I mean don’t get me wrong, it was a great decade (I’m an 80’s baby!) but the home decor and design ideas from that decade were interesting, to say the least. The house I grew up in had green shag carpet, orange countertops and carpet in the kitchen! Oh my!

Now our farmhouse hasn’t been updated since the 80s. The living room had green and white laminate tile, (you can read all about that here) and laminate and traditional wood throughout the entire rest of the house. And in the kitchen a drop ceiling with fluorescent lights. There were actually fluorescent lights throughout most of the house. They were an affordable lighting solution back in the day. But times have changed! Which brings me to today’s post. How we demo’d our drop ceiling in the kitchen and removed the fluorescent lights.

This was a project we knew we wanted to tackle from the beginning but we knew it would be time-consuming and lots of electrical would need to be done.  I was recently talking to my bestie, Ashley about this and she mentioned that her hubby had experience installing recessed lights and she offered their help to tackle this project. So we set the date and got to work.

The nice thing about this drop ceiling was that originally the entire kitchen was covered in drywall and this drop ceiling was added onto that. This meant that we just needed to remove the drop frame that was built and the fluorescent lights. Another interesting fact about this house is that the kitchen ceiling is actually about 18″ below the attic space. So at one point the kitchen ceiling was taller and was “dropped” not once but twice! We have no plans at the moment though to take it back up to the original height.

This post contains affiliate links for your convenience, this means that if you click on a link and end up making a purchase I will receive a small commission at no additional cost to you. See my full disclosure and privacy policy for more information. Materials Used to Remove Drop CeilingPlastic sheeting for dust controlWork LightsHammerDrillPrybarMulti-tool (this is the one Justin used)Hole saw drill bit (we used a 4″ and 6″)Sawzall Removing Fluorescent Lights

Our first step was to remove the lighting. The lights were covered by plastic sheets inserted on a metal frame. so down those came. The lights came next. It was definitely helpful to have two of us to help take down these metal light covers as they were very heavy.

Most importantly make sure  your breaker is shut off. We used work lights that plugged in to keep a light in our work space.

And it was very helpful to close off all the other spaces so that that dust and debris stayed in one place.

We did stumble upon some “interesting” electrical work during our removal of the light that was over the sink. It was plugged into an outlet that was near the ceiling, we never used this light so it wasn’t a big deal to us but the electrical was definitely a little skeptical. Removing the Drop Ceiling Frame

After the lights were removed the next step was to remove the frame that created the drop ceiling. The nice thing about this is that this “drop” was added after the rest of the ceiling so there would be minimal drywall repair at the end. Justin cut the drywall loose with his Milwaukee multi-tool which made removing the drywall and frame a little easier with less mess.

After all the drywall was removed we were left with the wood frame that had been bolted to the ceiling and nailed into each wall. Justin and Brad removed this in sections, first remove the bolts from the ceiling and then using his Sawzall to cut through the nails attaching it to each wall.

This is where Ashley and I came in and started to help clean up the space as best as possible so they could start working on electrical. Be prepared for a lot of dust! I am still finding dust in spots even though I wiped down and mopped! Installing Can Lights

Now I am not going to get too technical on the electrical instruction because well for one it’s complicated and you should definitely hire an electrician for the wiring part and two I just don’t understand it all myself. We were lucky enough to have our friend who is an electrician guide Justin and Brad through the process.

Luckily Justin and Brad had both had experienced before drilling the holes for can lights so Brad brought the hole saw drill bits that we would need. The 6″ hole saw drill bit was used for the can light and the 4″ was used for the lights over the island and the sink.

While we were adding the can lights to the kitchen we decided to add lights in the hall that leads to the garage as it is always very dark.

We were only able to completely finish two of the lights with bulbs this day because we ended up grabbing the wrong lights for the other cans. We went back to Home Depot the next day to get the correct ones. I feel like I live in that place sometimes, anyone else!!??

So above is the finished look of the kitchen that night after I had cleaned and mopped. Of course, you can tell this was before we took our trip to Home Depot. I will be sharing in another post all the finishing details of the new lights installed over the island and sink and show the updated space with drywall patched, textured and painted!

Share :